How to Clean Permanent Gold Teeth

Woman brushing her gold teeth

Are your permanent gold teeth looking less than perfect? Well, don’t worry; this blog post will show you how to clean your permanent gold teeth. We will guide you through effortless procedures that can be done in just a few minutes each day.

How to Clean Permanent Gold Teeth

There are many ways you can clean your gold teeth. However, the key is finding what works for you. Let’s look at some permanent gold teeth cleaning strategies you could incorporate into your gold teeth cleaning routine to keep them shiny.

Woman brushing her gold teeth

Brushing

Brushing your permanent gold teeth is different from how you brush regular teeth. Scrubbing too hard with coarse bristles can gradually erode the gold coating of your crown. How to brush your gold crowns may be more important than the toothpaste you use.

When brushing, do it gently for about two minutes. Rinse with a fluoride mouthwash to kill bacteria on your gold teeth. Stiff bristles and forceful brushing can damage your gold teeth and put you at risk of tooth decay.

Stick to soft bristles, especially for electric brushes.

Using a Toothbrush and Warm Water

This is the cheapest and most common way to clean your gold teeth. Scrub away with a toothbrush and warm water to remove plaque and other stains from your permanent gold teeth.

Using Gel Toothpaste

You might be tempted to use the same toothpaste for gold teeth as you do for your regular teeth, but a gel-type toothpaste is more effective at removing stains. Gel toothpaste is made of smaller particles than regular toothpaste, so it’s better to penetrate gold teeth and get rid of tough stains.

Toothpaste formulated especially for gold teeth also contains polishing agents that help remove stains, making them effective even if you don’t use a gel type. Toothpaste is also helpful in other hygiene kit in your bathroom like cleaning your safety razor.

Using a Special Solution

You can purchase a cleaning solution like hydrogen peroxide and salt for your gold teeth from your dentist or from stores that sell dental supplies. Hydrogen peroxide is an agent for cleaning metal surfaces which is great for cleaning your coins and other metals. Follow the instructions on the solution bottle to ensure that you are using it correctly.

Using Whitening Strips or Gels

If you want to bleach your gold teeth, various teeth whitening products work well with gold. As always, make sure to follow the directions on the packaging if you use this method.

You can also achieve similar results at home by putting some lemon juice on a cotton ball and rubbing it on your gold teeth.

Adding Baking Soda to Your Toothpaste

If you do not want to purchase an entirely different cleaning product, adding baking soda to your toothpaste could be your remedy. A baking soda-toothpaste solution is more substantial than just brushing with water.

You can put some baking soda in your toothpaste when you brush. This will give your toothbrush the extra scrubbing power you need to clean your gold teeth.

Additionally, baking soda is a powerful cheap cleaner that is helpful in removing stains and cleaning your vehicle’s radiator.

Using Baking Soda and Lemon Juice

A similar mixture to the one mentioned above combines baking soda with lemon juice. Once again, you can either dip your toothbrush in a small cup of this mixture or directly apply it to your gold teeth.

Thoroughly rinse your mouth out after using both of these methods.

Using Baking Soda and Hydrogen Peroxide

Another DIY option is to mix baking soda with hydrogen peroxide, which creates a foaming mixture that can be used for gold teeth cleaning. This works in much the same way as the lemon juice method mentioned above.

You can also create an equally effective formula by mixing salt with vinegar, though less effective. Just like baking soda, vinegar is a powerful cheap cleaner that we can see in our kitchen, it is the main ingredient when you clean your ceiling fan.

Teeth cleaning by a dentist

Using Alcohol-free Mouthwash

Gold teeth are often stained by smoking or drinking, so a good mouthwash can help you keep your permanent gold teeth clean and looking their best.

  1. Put some in a small cup.
  2. Dip your toothbrush in it before scrubbing away at your permanent gold teeth.

It’s also a good idea to use mouthwash after meals to remove any lingering food particles that could later cause stains. An example is Listerine. Listerine has been a leading brand of mouthwash and dental rinse in the U.S.

Using Mouthwash and Baking Soda

You can use a simple mouthwash – baking soda mixture to curb plaque build-up on your gold teeth. However, this is not as effective as other mentioned methods.

Before scrubbing, you can either pour some mouthwash into a small cup or dip your toothbrush into the mouthwash. Follow this up by dipping the toothbrush into some baking soda.

Using Denture Tablets

Denture tablets can be bought from your dentist or ordered over the counter from a pharmacy. They contain chemicals that break up stains on gold teeth and help whiten them. It would help if you used these at least once every six months or regularly to keep your gold teeth looking their best.

You can get advice from your dentist on a specific brand or type of denture tablet that is good for cleaning gold teeth. Go for denture cleansers that are gentle and effective for cleaning gold teeth.

Denture tablets can keep your gold teeth looking new. Ensure you wipe off the excess with a damp cloth before allowing them to dry completely.

Flossing

Flossing is essential for good dental health, even though flossing around your gold teeth can be hard to do. Food stuck between your gold teeth can cause problems like staining or worse.

The easiest way to avoid this problem is to take your time flossing after eating, so you permanently remove leftover food before it has a chance to get caught up in your gold teeth. Adding a flossing routine to your gold teeth care will eliminate plaque better than just brushing.

Daily flossing will keep your gold teeth from getting stained or covered in debris. There are various types of floss, so find the one that works best for you and use it every day.

Using Dental Picks

Dental picks can help get into the small spaces surrounding your gold teeth. They are even more helpful if you have bridges covering some of your permanent gold teeth. They will allow you to clean all of your permanent gold teeth at once.

Using a Water Pick

Water picks effectively remove deep stains from your gold teeth, providing a more thorough cleaning. Instead of manual brushing, water picks use water pressure to remove stains and other debris between your gold teeth.

Gold Polishing Rag

A gold polishing rag is the only way to polish your permanent gold teeth safely. While this method will not remove significant problems, it can keep them looking shiny and new in between your six-month dental appointments.

Gold teeth dentures displayed on the table

Having Regular Dental Check-ups

The bacteria in plaque feed the sugars in your food and drinks to form acids that can decay your gold teeth. Permanent gold teeth pose an increased risk of tooth decay and gum disease. It is essential to see the dentist every six months to examine and clean your gold teeth to prevent the build-up of bacteria.

What Not to Use When Cleaning Your Permanent Gold Teeth

You should avoid carrying out some approaches on your gold teeth. Here are some cleaning procedures we would advise against:

  • Whitening Agents: Do not use whitening agents in an attempt to whiten your gold teeth. While this will temporarily mask the yellowing or greying, it can also lead to problems like tooth sensitivity. It may even cause damage to your permanent gold.
  • Soda: Sodas contain acids that can wear down your enamel, which will make your permanent gold teeth more susceptible to staining. This applies not only to soda but to any beverages containing acids like citrus juice.
  • Vinegar: Vinegar is just as acidic as sodas and has the same potential for causing problems with tooth enamel. However, you should never use vinegar on your teeth, even if you are trying to whiten them.
  • Salt: As with the other methods mentioned above, salt is often used for cleaning gold teeth by mixing it with another ingredient like lemon juice or baking soda. However, avoid using salt directly on your teeth because this could cause damage to your enamel.
  • Alcohol: While you might not think of alcohol as an ingredient in teeth cleaning products, it is sometimes used for its antibacterial properties. However, it would help if you tried to refrain from products with alcohol because the effect will only last until the alcohol has evaporated, leading to more harmful bacteria growing back in.
  • Jewelry cleaners: Silver and gold jewelry cleaners are for ornaments worn on the outside of the body. You will find a label on the solution bottle warning against ingestion.

Regardless of the product you are using, be sure to read the label on the bottle to protect you from ingesting something that would have you take a trip to the emergency room.

Conclusion

Keeping your permanent gold teeth clean is essential to avoid leaving stains or debris that can cause problems down the road. You have to be more vigilant than with regular teeth. Be meticulous with your gold teeth cleaning routine to maintain your golden smile.

How to Clean Wooden Toys

Colorful wooden toys on table

Cleaning wooden toys are important especially for the safety of children against diseases and bacterias that can lurk around in dirty areas. Wooden toys should be treated properly especially during the cleaning process since it is prone to deteriorate if exposed in certain liquids. Here’s how to clean wooden toys and maintain them.

Colorful wooden toys on table

Why Choose Wooden Toys?

There are several types of materials–such as plastic and synthetic ones–that toys are made of. While you can choose other materials for your children’s toys, wooden toys can be a good choice for them due to their natural and eco-friendly materials as well as other health-related factors incorporated to it.

Wooden toys help with children’s creativity and social skills. Wooden toys require imagination and creativity compared to spoon feeding vibrance of plastic toys. These are mostly blocks and puzzles which can also be a good way for them to connect with other children in terms of problem solving and building skills.

Things You Need for Cleaning Wooden Toys

Cleaning wooden toys is simple and easy to do and having the right materials and cleaning agents with you will make it a lot easier and time saving. Cleaning wooden toys is much more delicate compared to cleaning other types of materials. With that in mind, here are the things you need for cleaning wooden toys:

  • Proper liquid cleaning agent such as vinegar and water solution, mild dish soap, plain warm water, or non-toxic multipurpose cleaner and water solution
  • Bottle spray
  • Wash cloth
  • Sponge
  • Mineral or olive oil

Different Methods in Cleaning Wooden Toys

There are different methods in cleaning wooden toys. Since wooden toys are made of natural materials, they are prone to deterioration especially when soaked and exposed with water. With that, it’s best to maintain them with cleaning depending on what kind of dirt they have accumulated over the past days and weeks.

Overall Cleaning

If the wooden toy needed an overall cleaning, you can do that by choosing your preferred cleaning agent and apply it all-over the wooden toy using a sponge or a washcloth. You can also do that through a spray bottle to cover a bit more areas and gently wipe the toy with a damp washcloth or sponge to get rid of the solution.

Little kid playing with his wooden toys

If the wooden toy is varnished and painted, you can choose a more thorough cleaning process by using a mild dish soap. This soap is similar to what you use for cleaning your wooden comb, your lava rock beads. Additionally, a sponge to clean the dirt and rinse it with water.

Varnished and painted wooden toys tend to be more resilient in water because of the water resilient layers painted in their exterior.

After the cleaning process, the best way to dry the newly cleaned wooden toys would be putting them in the sun for a natural drying method. Also, this can help with preventing bacterial and dirt build-up during the drying process since bacterias and germs tend to stay in moist areas.

Dry Cleaning

You also clean your wooden toys by simply wiping them out with a dry clean towel and washcloth everyday. Children tend to put toys in their mouths and suck on their toys whenever they have the chance so there is a big possibility of bacterial build-up if the saliva stays in the wooden toys.

Wiping them with a dry cloth everyday is actually necessary just like regularly cleaning your treadmill belt when you exercise. Not just to maintain the wooden toys in its top shape but also to prevent diseases. It can also prevent conditions obtained through bacterias in germs that might lurk into children’s unchecked and unclean surroundings, things, and toys.

Cleaning will help them to maintain their good health and safety during playtime.

Stain Cleaning

Overall cleaning of wooden toys is a must, but they should be done in moderation since too much cleaning will compromise the integrity of the wood. You can get rid of specific and stubborn stains in wooden toys by spraying vinegar and warm water solution to the area. Vinegar is also helpful in cleaning your wood blinds in your home.

Wooden Toys Care and Maintenance

Wooden toys need to be maintained in order to have a longer life span. Toys with natural materials such as wood are durable and will withstand the test of time if given the proper care. Thus, it is important to know what type of care, maintenance, and safety reminders you need for wooden toys.

Care Tips and Reminders

Wooden toys are natural and eco-friendly items that children absolutely adore. However, there are things that you need to look out for whenever you purchase a new wooden toy or let children play with some. Despite known for being harmless, here are the care tips and reminder about wooden toys:

Curvy wooden toys playing by a kid
  • Newly purchased wooden toys tend to have a strong smell of either paint and varnish in them. You can remove this smell by spraying them with cleaning agents and wiping them with clean cloth.
  • Wooden toys have come in different shapes and sizes which can only be applicable in certain ages. For instance, wooden puzzles and build-type wooden toys are more applicable in children ages 7 and up since they come with small parts that can be chokable for toddlers. Go for big wooden toys for toddlers and children ages 6 below to prevent choking hazards.
  • Thoroughly inspect wooden toys before buying them for children. There are a few wooden toys in the market that have rough and pointy edges that are not child-friendly, especially in toddlers.
  • Always have supervision during play times to avoid and prevent any possible wooden toy related accidents. Wooden toys can be hard and heavy for certain age groups which causes small yet manageable accidents for them.

Wood Replenishing and Maintenance

Wooden toys and other things that are made of wood should be maintained. So, it can retain its integrity and quality for a long time. With that, proper moisturization is needed in order to avoid cracks, roughness, and brittleness.

You can use olive oil, mineral oil, and beeswax polish to moisturize them.

Drop a bit of your preferred moisturizing agent to the wood and gently wipe it using a clean washcloth. The reason is to help the oil spread evenly on the surface. You need to do this regularly when wooden toys look dull and dry in color.

Also, you need to moisturize them every after overall cleaning to retain its good finish.

Conclusion

Cleaning wooden toys is important and easy to do. You can clean wooden toys by spraying and wiping them with a non-toxic cleaning agent. Also, drying them under the sun to prevent bacterial build-up caused by moisture.

After drying, apply olive oil using a washcloth to moisturize the wood for maintenance.

How to Clean Treadmill Belt

Woman running on treadmill belt

If you have a treadmill in your home gym, it is probably one of the most expensive items there. You do not want to see your investment go down the drain by not taking proper care of it. This is why you have to learn how to clean it, especially the belt.

How to Clean Your Treadmill Belt

Cleaning your treadmill belt is not an expensive procedure. It is a simple process that you can incorporate into your weekly routine. It will save you money that you would have otherwise spent on repairs in the long run.

Woman running on treadmill belt

Dirt, grime and sweat are the enemies of your treadmill belt. These you have to remove right away; if you let them build-up, you will have permanent stains. When maintained properly, it will increase the lifespan of your machine.

You’re probably thinking about grabbing something and wiping the surface, and you’re good to go. That is not how it is done. This article will guide you on how to properly clean your treadmill belt.

Cleaning the Top Surface

The things you will need for this are:

  • Dry cloth
  • Paper towel
  • Clean damp cloth
  • Disinfectant

You mustn’t use any cleaning materials or sprays unless the manufacturer recommends them. The same goes for cleaners used to shine the metal parts. They may cause the treadmill to become slippery, which is dangerous and can cause accidents.

Follow the following steps to clean the top of your treadmill belt:

Step One

Disconnect the treadmill from the power source.

Step Two

Use your clean damp cloth to wipe the surface of the treadmill belt. You can wear an old T-shirt for this. To make sure that it is the correct level of dampness, it should not leave your hands wet.

It should also not drip water into the surface. Rotate the belt with your hand and wipe the rest of the surface until you have covered the whole belt.

Additionally, clean cloth is also helpful in cleaning your instruments like cymbals.

Step Three

Take the dry cloth, add a little disinfectant to it and wipe the top surface of the treadmill. The same way you rotated the belt in the previous step, do it again, this time with the cloth with the disinfectant.

This dry cloth can also help to clean your Coleman grill inside your house.

Step Four

Using the paper towels, dry the treadmill belt. Rotate the belt to ensure it is dry.

Cleaning the Underside

It is easy to see that the top of the treadmill is clean, and so you end up neglecting the underside. Clean it in the following easy steps.

Step One

Take a dry cloth, make sure that it is clean and larger than the width of the treadmill belt. Lift the belt carefully and slide the cloth below it.

Step Two

Move the cloth steadily from one end to the other end. You will notice some dust and debris on the piece of cloth; wipe until it is clean.  If you want to disinfect this part, go ahead.

Man walking on a black treadmill belt

Step Three

Rotate the belt manually and repeat the process of moving the cloth until you notice that it is clean.

Ways to Take Care of Your Treadmill

Cleaning the treadmill belt is one way of taking care of it and making sure that it lasts for a long time. The following are other ways to make sure your treadmill belt is well taken care of.

Lubrication

How do you know your treadmill is sufficiently lubricated? Using your finger, touch the deck surface under the walking belt. If it feels oily or waxy, then it is okay. If your finger is dry, you need to lubricate it.

Lubrication is crucial as it reduces friction between the motor and the treadmill. Ensure you use a lubricant that is designed for treadmills. Regular lubricant is not suitable as it cannot withstand the heat that the treadmill generates unlike cleaning your bike chain can only apply a regular oil for lubricating.

When applying the lubricant to the machine, rotate the belt manually. Lubricate your machine every three months with a silicone lubricant or something that the manufacturer of your treadmill recommends. The wrong type of lubricant will ruin your treadmill.

Wipe the Treadmill

You have probably been to the gym and seen people who wipe the treadmill after using it and those who come in and wipe the machine before they go. You may have thought it was because of someone else’s sweat or something gross.

Wiping the treadmill after use is hygienic and a great way to prevent corrosion of the belt and the frame. Wipe your treadmill after use so you can enjoy it for a long time to come. A piece of cloth would work perfectly. You do not need fancy detergents.

Vacuum Frequently

You have to regularly remove dust and dirt from your treadmill before it accumulates and causes problems. Do this in areas around the belt and the treadmill deck. When dust and dirt accumulate, they damage and wear down the belt.

Vacuuming is essential in different rugs and helpful in cleaning your area rug on your floor.

For this reason, do not get on your treadmill with shoes that you wore outdoors. They have dust and dirt that will most likely end up on the belt. When vacuuming, do so on the belt and on the underside. Have a cloth for getting to areas that the vacuum cannot.

Some treadmills have an open design with high chances of the motor and cover becoming clogged. Everything from hair, dirt and dust will get into the motor. If you do not remove it from there regularly, you are going to end up with a huge problem.

Get a Treadmill Mat

A treadmill mat primary function is to protect the floor that your treadmill is on. It will also protect your treadmill. Your hardwood or carpet will get protection from wear, and the treadmill mat will prevent sweat from getting to the floor.

If you happen to have anyone living below you, the mat will prevent most vibrations from the treadmill. You do not want to be the annoying neighbour, right? A treadmill mat will also make things easier for you when vacuuming as it prevents dust, dirt and hair from getting to the motor.

To get you sold on the idea of a treadmill mat, think of how much your floor cost and the price of the treadmill. They will both last much longer if you get the mat. Get a high-quality mat for your treadmill and give your machine and floor more years.

Adjust and Tighten Belt

Most manufacturers sell treadmills when the belt tension is already adjusted. However, with repeated use, it will start to loosen. The tension decreases on the deck as the belt stretches.

You will be able to tell this as you will feel the belt is moving too much and is slippery.

To rectify this, tighten the two bolts at the end of the treadmill deck, and your tension will be fine. Check the buyer manual for more guidance. When the belt loosens, it may move closer to one side, thus getting off centred.

Immediately centre it to reduce any accidents.

The same bolts you used to get the tension right are the same ones you will use to centre your treadmill. Tighten the right bolt to centre the belt to the right and the left bolt to centre it to the left. Always check your manual when you are unsure how things should be done.

Man walking on a black treadmill belt

Additional Tips

Other things that may help your treadmill last longer include:

  • Unplug your treadmill when it is not in use
  • Use a surge protector
  • Set your machine on a level surface
  • Call a professional when you encounter a problem you are unable to handle

A Worn Out Treadmill

According to the U.S  Consumer Product Safety Commission (CPSC), treadmill accidents may not be common, but they can be very dangerous when they occur. You may do all that is necessary to maintain your treadmill, but it will become worn out with time.

How do you know it is time to replace your treadmill?

  • The treadmill belt is discoloured and smooth due to excessive wear.
  • You have had it for a long time. It has been repaired countless times.
  • The motor makes irregular high-level sounds when you use it, but you cannot seem to find the problem.
  • The frame is shaky or damaged due to usage and movement.
  • The console electronics are acting up, or they do not respond, indicating a short in the electrical connection. This may end up causing an electrical fire or electrocuting you.
  • The parts cost too much. Sometimes, replacing it may be the best option instead of buying new parts every time your treadmill is damaged.
  • It is outdated.

When looking to replace your treadmill, do thorough research. Look at the things that your old machine did not have that you would like to have in your new one and go for that. You may have to look for experts to know which is the best for your needs. Remember the cleaning tips.

Conclusion

Like most machines, cleaning and maintenance go a long way to ensure that your machines serve you for a long time. Follow the tips above and the instructions from the manufacturer of your machine, and you will enjoy using your treadmill for a long time.

How to Clean Skateboard Bearings With Household Items

Skateboard on the gutter

Maintaining skateboard bearings is much easier than it sounds. In fact, you can clean skateboard bearings using simple and common household items lying around your home. Not only that, you will also be astounded by the number of alternative cleaning agents you can use that are far cheaper and safer for the environment.

Skateboard on the gutter

Before the cleaning process, make sure that you are well adverse with disassembling and reassembling your skateboard, wheels, shields, and bearings. Knowing this process will allow you to clean your bearings at home. If you are not knowledgeable about the process, ask help from a professional.

Things You Need to Clean Skateboard Bearings

Cleaning skateboard bearings are convenient especially when you know what kind of household items you will be using. While cleaning projects such as this can boost one’s creativity when it comes to looking for the proper items to use, having the accurate and exact household items will help smoothen the cleaning procedure.

Securing the household items is quite easy especially if you are familiar with your household’s organization system. Here’s a list of the things you need to clean your grimy skateboard bearings. Note, they are commonly found somewhere in the kitchen, trash drawers, garage, and tool cabinets:

  • Socket wrench – for disassembling and assembling skateboard wheels.
  • Paper clip or safety pin – for prying with bearing’s seal.
  • Hair dryer – for speed drying the bearing after cleaning.
  • Machine oil used in gadget or sewing machines – for the bearing’s lubrication.
  • Diesel, acetone, alcohol, or other circus cleaning agents – for dissolving the dirt and cleaning the skateboard bearing.
  • Dishwashing soap – for removing strong cleaning agents.
  • Water – mixed with dishwashing soap for removing strong cleaning agents.
  • Empty jar with lid – used as a container to soak the bearing using cleaning agents.
  • Dry and clean towel or rag – for removal of dust and dirt before cleaning as well as drying the bearing after.
  • Hair dryer – for better drying process.

How to Clean Skateboard Bearings Using Common Household Items

The first thing to know about cleaning skateboard bearings is to carefully follow the steps and instructions given. Understanding the cleaning procedure is vital in order to maintain the skateboard bearings and not accidentally ruin it during the process. Here’s the step by step procedure in cleaning dirty bearings using household items:

Remove the Skateboard Wheels

The first step is to remove the skateboard wheels in order to get the bearings placed on each side of the wheels. You can use a socket wrench to loosen the axle nuts attached to the screws. After removing the socket wrench you can now proceed to remove the screws and axle washers.

Finally, place them in a safe place for reassembling after you are done cleaning.

Remove the Bearings From the Wheels

There are two bearings placed on each side of skateboard wheels. Make sure to remove them all by carefully inserting the tip of the truck axle into the bearing and pulling it out. Also, handle the removal of the bearing cautiously as force will tend to damage or break the bearings especially during the pulling process.

Remove the Shields

There are two types of skateboard shield, the older models and new ones. The older models are made of metal secured with snap rings or circlips, while the new models are usually made of rubber or nylon. With that in mind, there are also different ways to remove the shield based on their models or types.

Skateboard with style leaning on the wall

If you have the older models which are made of metal, you can use a safety pin or a paperclip and find one of the circlip or snap ring’s end located in the outer side of the shield. Lift it up and remove it. After that, you can remove the shield in the bearing at ease.

If you have the new models which are made of either nylon or rubber, you can use a safety pin or a paperclip to pry out the shield from the bearing. Remember to be careful as shields that are made of materials such as nylon and rubber tend to be prone to breakage if mishandled. Make sure to remove the shield with care to avoid damage.

Clean the Bearings

There are a lot of cleaning agents that you can use to clean bearings. Before soaking them into one, make sure to clean the oil and dirt in the bearings using a dry cloth or towel to help with the cleaning process. This process can also apply in cleaning your dirt bike air filter.

Here are some of the cleaning agents you can use:

  • Acetone – Acetone is the most commonly used in cleaning bearings.
  • Diesel  – Diesel removes rust and prevents rust and oil buildup which can be great for cleaning skateboard bearings.
  • Alcohol – 90% isopropyl alcohol can be an acetone alternative since it evaporates quickly and prevents rusting in bearings. This can also help to regain the shine and clean your safety razor.
  • Citrus cleaner – You can also use citrus cleaner for bearings, just make sure to use the non-water based ones to prevent rusting.
  • Lemon juice – lemon juice can be a good alternative to citrus cleaners as long as you avoid using water to add into the solution. This is helpful in cleaning your musical instruments like cleaning your cymbals, as well as cleaning your drum heads and other instruments.

Soaking your bearings into your preferred cleaning solution for about 5 to 7 minutes enclosed in a jar. Using a jar will prevent the bearings from rusting as well as to help the cleaning agents amplify their effects. After that, you can start removing them one by one when the dirt and oil dissolved.

Remove the Cleaning Agent’s Residue

After removing them from the soaking and cleaning process, you have to remove the cleaning agent’s residue in the bearings. This is applicable for cleaning agents like diesel and machine oils which are hard to remove using dry cloth. You can use dishwashing liquid or soap for residue removal and rinse it with running water thoroughly.

Now, using water can cause rust in bearings which will eventually cause deterioration, leaving the bearings useless over time. Thus, you have to rinse them using a bit of alcohol or acetone after rinsing. Alcohol and acetone are water-based spirits that can evaporate instantly which will prevent the rust build up.

Pat and Dry

After the cleaning process, you have to dry the bearings to prevent it from building dirt and rust. Also, this pat and dry process in order to prepare the bearings for the next vital process which is lubrication. You can use a dry cloth to pat the bearings until it dries and you can also use a hair dryer to make sure that the bearings are thoroughly dried.

Put Lubrication

The next vital step before reassembling your clean skateboard bearings back to your skateboard wheels would be lubrication. Lubrication is important in skateboard bearings in order to maintain their lifespan and performance. It helps with separating the moving parts of the bearings to one another that prevents possible damage and tear due to friction.

You can use machine oil for gadgets and sewing machines to lubricate your bearings. If you are looking for a household alternative, coconut oil can also be used for lubrication. You can also use motor oil or cooking oil if you do not have anything you can use for lubrication in your household.

These oil alternatives can also be used to clean your bike chains for lubrication.

Reassemble the Skateboard Bearing and Wheels

After lubrication, you can now reassemble your skateboard bearings and wheels together. Before putting back the disassembled pieces of your skateboard, make sure to clean them thoroughly using a dry cloth. Afterwards, you can carefully put back the small and sensitive parts to avoid damage.

Man holding a skateboard and coffee

Important Tips and Reminders

Aside from learning how to clean your own skateboard bearings, it is also crucial to understand how important they are in your skateboard’s performance and how to properly take care of your bearings while using them. Here are some vital tips and reminders about the importance of skateboard bearings and skateboard maintenance:

  • The main function of skateboard bearings is to allow your wheels to roll. Thus, bearing is an important part in your skateboard’s all-over function and performance.
  • The condition of your skateboard bearings will determine how fast and smooth your skateboard can go which is why you need to maintain your skateboard bearing through proper cleaning and lubrication to improve your skateboard’s speed and performance.
  • A skateboard bearings have 5 major parts: the shield, inner race, balls, retainer, and outer race.
  • There are two types of bearings, the steel ones and the ceramic ones. The steel ones have steel balls inside them, while the ceramic ones have ceramic balls inside. The ceramic ones are more durable and faster than steel ones.
  • Choosing your bearings are crucial in order to control the speed of your skateboard. For instance, beginners can use typical and cheap bearings than high-quality ones since the latter have more speed and power than can be hard for beginners to handle.

Conclusion

Cleaning skateboard bearings with household items is easy as long as you know how to assemble and reassemble your skateboard parts. You can soak your bearings using common cleaning agents in the household like alcohol and acetone. After drying and lubricating, your bearings are now ready for reassembling and use.