As an Amazon Associate we earn from qualifying purchases.
If you have been wondering how to clean stainless steel jewelry, you’re not alone. It seems like someone is wearing some stainless steel jewelry everywhere you look these days.
It’s used in everything from watches and rings to necklaces and earrings. When it becomes dirty, dulled, or tarnished with time, this becomes a problem for cleaning stainless steel jewelry.
But don’t worry because there is a simple solution that will work no matter what type of alloy your jewelry is made of.
Here are ways to get sparkling results with clean stainless steel jewelry.
Contents
The Simple Way: Soap and Water
1. Take a bowl and fill it with warm water. Next, add just a few drops of soap into the mix and stir until completely dissolved.
2. Submerge your jewelry piece in the bowl and allow to soak for 5 minutes. This will help loosen up any dirt or debris stuck on your jewelry piece’s surface. Be sure not to let the metal sit too long as this can cause it to corrode or rust!
3. Use an old toothbrush (or any soft-bristled brush) to gently scrub all over your jewelry piece until you see all the dirt and grime build-ups disappear before your eyes! Just be extra careful if you’re using a toothbrush with hard bristles.
4. Rinse the jewelry piece under warm water to remove all the soap residues and then dry with a soft cloth or paper towel.
The Fancy Way: Baking Soda Paste
Method 1
1. Take a bowl and add just enough water to create a thick paste; you don’t want the mixture too runny because this will not clean your jewelry properly. You can always add more water after baking soda to make up for what has evaporated while mixing.
2. Add in two tablespoons of baking soda. The addition of this ingredient helps loosen any tough dirt and grime, especially on more intricate pieces where it may be too difficult to get in with a toothbrush. This method is also quite effective for cleaning rubber watch bands.
3. Stir the mixture until an even consistency is achieved throughout; add more baking soda or water if needed.
4. Submerge your jewelry piece in the bowl and allow to soak for 5 minutes. This will help loosen up any dirt or debris stuck on your jewelry piece’s surface. Be sure not to let the metal sit too long as this can cause it to corrode or rust!
5. Gently scrub all over your jewelry piece using a soft-bristled brush, just like how you would make cookies. Mix all ingredients until even consistency is reached! It’s important to remember that too much water can be bad for your jewelry, so try your best to get the right water balance and baking soda to avoid any potential accidents or damage!
6. Rinse the jewelry piece under warm water to remove all paste residues and dry with a soft cloth or paper towel.
How To Clean Tarnished Jewelry
Method 2
1. Take a clean cloth and moisten it with water, wring out any excess liquid so that it’s damp but not soaked.
2. Squirt a dab of toothpaste onto the damp cloth. This works best when you use toothpaste specially planned for stainless steel surfaces or silver, as others can cause your jewelry to leave behind unwanted residue or discoloration.
3. Rub the toothpaste all over your jewelry piece in a gentle circular motion, paying close attention to areas with deep-set stains and dirt.
4. Rinse under warm water and pat dry with a clean towel or paper towel!
Cleaning The Natural Way: Toothpaste
1. Take a bowl and add just enough water to create a thick paste; you don’t want the mixture too runny because this will not clean your jewelry properly. You can always add more water after baking soda to make up for what has evaporated while mixing. Like you would make cookies, mix all ingredients until an even consistency is reached!
2. Add in two tablespoons of baking soda. The addition of this ingredient helps loosen any tough dirt and grime, especially on more intricate pieces where it may be too difficult to get in with a toothbrush.
3. Gently scrub all over your jewelry piece using a soft-bristled brush, just like how you would make cookies. Mix all ingredients until even consistency is reached! It’s important to remember that too much water can be bad for your jewelry, so try your best to get the right water balance and baking soda to avoid any potential accidents or damage!
4. Rinse the jewelry piece under warm water to remove all paste residues and dry with a soft cloth or paper towel.
5. If you notice your piece is particularly tarnished, repeat steps 1-4 until desired results are achieved! Remember always to test how effective the mixture is on a hidden part of your jewelry piece first before submerging it into the solution for a prolonged period, as this might damage your precious metal alloy if overused.
There are tons of different types out there, so you must know how to care for each one appropriately to keep them looking shiny and new. Here are the most frequently used jewelry alloys and how you can clean them best!
How To clean Stainless Steel Jewelry
Cleaning your stainless steel jewelry yourself is the best way to preserve its original quality and shine. You don’t want to spend all of that time picking out how you’re going to wear it, only for it to end up tarnished or dirty after one day!
Even slightly dirty pieces can lead people to doubt how much you care about how you look, so keep this in mind if you want it to last.
Tarnished and dirty stainless steel jewelry pieces can be cleaned using baking soda, water, and a soft-bristled brush like how you would make cookies! This is the best way to get your piece sparkling clean while maintaining how it originally looked when you first bought it.